馬達使用注意事項　Instructions

1.當你使用馬達時，不可有束縛之物，如接著劑不要經過旋轉軸流入軸承，妨害馬達的運作。

2.軸的轉動對馬達之壽命可能有相反的效果，為了壽命的延長，請檢查你的負載品是否依照規定，不可超負載，或軸端掛有妨害轉動的物品。

3.制造成偏心之重幅射負載，有害馬達之壽命。

4.請勿貯藏于四周高溫或極端潮濕中，也請勿放置在腐蝕瓦斯中，會使馬達效果降低。

5.馬達請勿運轉在周圍高溫與潮濕中。

6.電源正負極的馬達端子上要焊錫時，烙鐵溫度340℃±40℃、加熱時間3秒鐘以內，不可使塑料變形，在工作中，讓焊錫點流入馬達或折斷電線末端，這樣會使馬達功能衰退。

7.不可讓馬達軸卡住，當傳入電力時，在短時間內會使馬達過熱，燒毀其附屬品。
8.因工作人員缺乏技術，使馬達遇說明書提及之事，或表面判斷顯然是過失時，是無法保證質量。

9.供應規定電力，確信在可測要求范圍內。

10.滑輪或齒輪的安裝，在壓入時不要異常的加重。

11.安裝馬達之時，螺絲釘過長，會造成馬達本身和轉子間發生接觸，會影響特性。

1. When you use a motor, not bondage thing, such as adhesives do not after rotation axis inflow bearing prejudice to the operation of the motor.

2. The axis of rotation of the life of the motor may have the opposite effect, for longevity, check whether you load goods in accordance with the provisions of, not ultra-load, or the shaft end prejudice rotation of items hanging.

3. Manufacturing the heavy radiation eccentric load, harmful motor life.

4. Do not stored at four weeks of high temperature or extreme humidity, do not place corrosive gas, causes the motor effects reduced.

5. The motor Please do not operation in the surrounding high temperature and humidity.

6. Power the positive and negative terminals of the motor to be solder, soldering iron temperature of 340 ° C ± 40 ° C, the heating time less than 3 seconds, not the plastic deformation work, so the the solder point into the motor or broken wire ends, this would allow the motor functionrecession.

7. Not to allow the motor shaft stuck, when the incoming power, motor overheating will make in a short time, and burned their accessories.

8. Due to lack of technical staff, the motor in case of manual mentioned things, or the face of it obviously is negligence, is unable to guarantee the quality.

9. Supply that power, sure can be measured within the requirements.

10. Pulleys or gears of the installation, in the press-fitting is not abnormal aggravated.

11. Mounting the motor when the screw is too long, can cause contact between the motor itself and the rotor, will affect the characteristics.